 |
1432
SHDSL CPE Router
Line Interface
- Applicable standards: ITU-T G.991.2, G.994
- Single pair or two pair line access
- Connector: RJ12/RJ45
- Impedance: 135 Ohm
- Coding: TC PAM, compliant ITU-T G.991.2 Annex A&B (G.SHDSL), ETSI TS 101524
- Line speeds: > Single pair: N x 64 kbps (N = 3 … 36)
- Two pair: N x 128 kbps (N = 3 … 36)
- Handshaking: compliant G.994.1 (automatic speed negotiation) or fi xed speed
- Dying gasp to indicate power loss to DSLAM
- Performance monitoring: compliant G.826 (errored seconds, severely errored seconds, unavailability seconds)
- Ideal maximum distance (noise-free)
- Applicable electrical standards: ITU-T V.10, V.11
- Connector: female DB25 (ISO 2110), directly compliant with RS530, RS530A
- Through adapter cable: V.35, V.36 (RS449), X.21
- DTE signals: SGND (102), TXD (103), RXD (104), CTS (106), DSR (107), DTR (108), DCD (109), EXTCLK (113), TXCLK (114), RXCLK (115)
- X.21 signals: G, T, R, C, I, S, X
- Layer 2 protocols: Frame Relay or transparent LAN port (2 pair version)
- Compliant with IEEE 802.3 10 Mbps HDX/FDX Ethernet
- Compliant with IEEE 802.3u 100 Mbps HDX/FDX Ethernet
- 10/100 Mbps auto-sense
- Auto cross-over
- RJ45 Unshielded Twisted Pair (UTP)
- Applicable standards: ITU-T V.24, V.28, EIA/TIA 574
- DCE signals: SGND (102), TXD (103), RXD (104)
- Connector: female DB9
- Speed: 9600 bps
- Internal Line Loopback (Analogue Loop)
- External Line Loopback
- Internal DTE Loopback
- External DTE Loopback (Digital Loop)
- Conform TDRE 12.0 (Total Dynamic Routing Engine)
- ATM Forum Traffic Management 4.0 service types CBR and UBR, VBR-rt, VBR-nrt
- Total number of ATM PVCs: 30
- ATM Forum af-vtoa-0078.000 Circuit Emulation Service (CES) version 2.0
- Clocking: internal preferred or alternative, slave on network preferred or alternative
- Interface speeds in internal and slave receive clocking: N x 64 kbps up to 2048 kbps (1 pair version) or up to 4096 kbps (2 pair version)
- User speeds: N x 64 kbps up to 2048 kbps/4096 kbps (1 pair/2-pair system)
- Can be combined with a low speed management PVC
- Frame Relay / ATM PVC Network Interworking Implementation Agreement (FRF 5)
- Frame Relay / ATM PVC Service Interworking Implementation Agreement (FRF 8.1)
- Number of user Frame Relay DLCIs: up to 30
- User speeds: N x 64 kbps up to 2304 kbps/4608 kbps (1 pair/2-pair system)
- Synchronous clocking: internal preferred or alternative, slave on net work preferred or alternative, external
- Synchronous interface speeds in external clocking: all speeds up to 2 Mbps (1 pair version) or 4 Mbps (2 pair version)
- Synchronous interface speeds in internal and slave receive clocking: N x 64 kbps up to 2048 kbps (1 pair version) or up to 4096 kbps (2 pair version)
- Conform TDRE 12.0 (Total Dynamic Routing Engine)
- Full forwarding performance of 64 byte packets at maximum interface speed
- Routing and bridging performance: 40 Kpps
- Number of IP VPN tunnels: 10
- Number of VLANs: 200
- Number of bridge-groups: 13
- Conform TDRE 12.0 (Total Dynamic Routing Engine)
- Preset button: check
- PWR: Power
- LINE / LNK1: fi rst line pair status
- LINE / LNK2: second line pair status (on 2 pair versions only)
- LINE / ACT: WAN encapsulation protocol status
- SERIAL / LNK: DTE connected (RTS) to the serial interface
- SERIAL / ACT: layer 2 status (in case of Frame Relay)
- LAN / ACT: LAN status
- Flash memory: 8 Mbyte
- RAM memory: 16 Mbyte
- Desktop (1 rack-unit high)
- Dimensions: 45 x 220 x 135 mm
- Weight: 500 g
- Wall mountable
- Rack mountable (optional 19” rack-mount kit required)
- Input voltage: 12 Vdc, max 1 A
- Power adapters for 115 Vac, 230 Vac, 24 Vdc and -48 Vdc
- Power consumption: 6 W (1P); 7,5 W (2P)
Copyright 2008 © OneAccess Networks, S.A. All rights reserved | Private policy